Spit HC6-15 Pulsa Pins 15mm x500 with Gas Cartridge 057555

Spit HC6-15 FH 057555 — 15mm Flush Head Gas Pins For Pulsa Fixing Into Hard Concrete & Steel

Spit HC6-15 FH 057555 pins are 15mm flush-head, collated gas nails designed for fast, reliable direct fixing into hard concrete, prestressed concrete and structural steel using Spit Pulsa gas nailers. With a 3mm hardened carbon steel shank, 6.4mm full flat head and mechanical zinc coating, they deliver consistent penetration, high success rates in tough substrates and internal corrosion protection on M&E and drywall jobs.

Short 15mm Pin For Thin Track & Fixtures

The 15mm length is ideal where you need secure holding power without excessive embedment, such as fixing drywall track, deflection heads, clips and small brackets to slabs, beams and cores. In non-cracked concrete at 15mm embedment, HC6 pins offer characteristic tensile resistance up to 0.87kN with recommended working loads around 0.30kN in tension and shear, giving dependable performance for light structural and containment fixings when edge distances and spacing are observed.

Flush Head Finish For Clean, Snag-Free Installations

HC6 FH pins use a special collation that fragments on impact so the head sits flush with the fixed material, reducing the risk of snagging on studs, boards, cable tray or pipework. That makes them a strong choice where a smooth finish is important, for example behind plasterboard, in risers, or around tightly packed containment runs.

Fast, Gas-Powered Fixing With Pulsa Tools

Supplied in strips of 10 pins with 500 pins and 1 gas fuel cell per box, HC6-15 FH pins are ready to load into Spit Pulsa tools for rapid repetitive fixing on site. They are suitable for use with Pulsa 27E, 40E/40P/40P+, 65 and 800E/800P nailers, covering most electrical and mechanical first-fix applications on concrete and steel. Installation is possible in any orientation – floor, wall or overhead – removing the need to drill and plug and significantly speeding up bracket and track installation.

Engineered For Hard Concrete & Structural Steel

Shanks are hardened to ≥56HRC and designed specifically for hard concrete from C20/25 to C50/60, prefabricated and prestressed concrete, and structural steels such as S235–S355. In steel, HC6 pins provide characteristic tensile capacities up to 3.74kN with recommended tensile loads up to 1.49kN and shear up to 1.20kN depending on embedment depth, helping to reduce failed shots and re-work when fixing into challenging substrates.

Typical applications include fixing drywall track and deflection heads, cable clips, saddles and light brackets to concrete soffits and walls, as well as direct fastening to steel beams and columns on commercial, residential and industrial projects.

Key Features Of Spit HC6 15mm Flush Head Gas Pins Include:

• 15mm Flush Head HC6 Gas Pins Designed For Dire:contentReference[oaicite:9]{index=9}d Concrete And Structural Steel
• Short Pin Length Ideal For Fixing Drywall Track Deflection Heads Clips And Light Brackets Without Excessive Embedment
• Flush Head Design With Fragmenting Collation Leaves The Pin Head Level With The Fixed Material For A Clean Snag Free Finish
• Hardened Carbon Steel Shank With Hardness Greater Than Or Equal To 56Hrc For Reliable Penetration In Tough Substrates
• Mechanical Zinc Coating Typically 10–20µm For Corrosion Protection In Dry Internal Environments
• Recommended Tensile Working Load Around 0.30kN In Non Cracked Concrete At 15mm Embedment For Light Structural Fixings
• Characteristic Tensile Resistance In Non Cracked Concrete Up To 0.87kN With Characteristic Shear Resistance 0.75kN At 15mm Embedment
• Characteristic Tensile Resistance In Steel Up To 3.74kN With Recommended Tensile Load Up To 1.49kN And Shear Up To 1.20kN Depending On Embedment
• Compatible With Spit Pulsa 27E 40E 40P 40P Plus 65 800E And 800P Gas Nailers For Flexible Site Use
• Supplied Collated On Plastic Strips With 10 Pins Per Strip 500 Pins Per Box And One Matching Gas Fuel Cell Included
• Suitable For Concrete C20 25 To C50 60 Prefabricated And Prestressed Concrete And Structural Steels Such As S235 To S355
• May Be Installed In Floor Wall Or Overhead Orientations To Speed Up First Fix Work Compared With Drilling And Plugging
• Ideal For Fixing Drywall Track Cable Clips Saddles Small Brackets And Light Containment To Concrete Soffits Walls And Steelwork

View All Capping Nails

View All Spit 

If you just need some help, would like to take advantage of our Price Promise or perhaps have a large order to place give our team of professionals a call on 0203 994 5470, drop us an email at sales@electricpoint.com or use our Contact Form.