dMEV Fans and Building Regulations

A dMEV fan only ventilates a home properly when the system around it is right. To meet the Building Regulations, it needs the correct extract rates, enough background ventilation, a permanent live supply and proper commissioning.

This guide explains how dMEV fans and the Building Regulations fit together in England, written for installers first and homeowners second. It covers trickle vent sizes, extract rates, wiring, Part P notification and commissioning, plus what changes when Approved Document F 2026 takes effect on 24 March 2027. New to dMEV? Start with our guide to what a dMEV fan is and how it works.

Which Building Regulations apply to dMEV fans?

Three parts of the Building Regulations can apply when you fit a dMEV fan:

  • Part F (Ventilation): guidance sits in Approved Document F, Volume 1: Dwellings. The 2021 edition currently applies in England. It calls dMEV “continuous mechanical extract ventilation” (System 3 in older editions) and lists it as suitable for all dwellings.
  • Part P (Electrical safety): covers the electrical work, including when work in a bathroom must be notified to building control.
  • Part J (Combustion appliances): applies if the home has an open-flued boiler, fire or stove, because extract fans can pull combustion gases back into the room.

Approved Document F 2026 was published on 24 March 2026 alongside the Future Homes Standard. It takes effect on 24 March 2027 (24 September 2027 for higher-risk building work), with transitional arrangements for projects already under way. We cover the changes near the end of this guide.

Approved Documents describe one way to meet the regulations, and the building control body has the final say on each project. Wales, Scotland and Northern Ireland set their own rules, so check local guidance if you work outside England.

Do I still need trickle vents with a dMEV fan?

Yes, in almost every case. A dMEV fan only extracts air, so replacement air has to get in somewhere. For continuous extract, Approved Document F 2021 asks for a background ventilator, such as a trickle vent, of at least 4,000 mm² equivalent area in each habitable room, and none in the wet rooms where the fans sit.

Trickle vents let fresh air into bedrooms and living rooms. That air then moves towards the wet rooms, where the dMEV fans remove it along with moisture and smells. A vent in the wet room itself would let air short-circuit straight to the fan and leave the rest of the home under-ventilated.

Air also needs a path between rooms, so undercut internal doors. Approved Document F asks for a free area equal to a 10 mm undercut on a 760 mm wide door: 10 mm above the floor finish, or 20 mm above the floor surface if the finish isn’t down yet.

How much background ventilation is needed?

For homes with continuous mechanical extract ventilation, paragraph 1.64 of Approved Document F sets three conditions for background ventilators:

RequirementWhat it means
LocationNot in wet rooms (kitchens, utility rooms, bathrooms or WCs)
Minimum sizeAt least 4,000 mm² equivalent area in each habitable room, such as bedrooms and living rooms
Minimum numberThe number of bedrooms plus two. A one-bedroom home needs at least three ventilators, a two-bedroom home four, and a three-bedroom home five

Equivalent area measures how much air a vent actually lets through, not the size of the slot. Use the equivalent area stated by the window or vent manufacturer.

If windows are replaced in a home that has, or will have, continuous extract, the new windows outside the wet rooms should include background ventilators of at least 4,000 mm² equivalent area in each habitable room.

Natural ventilation with intermittent fans needs far more: 8,000 mm² per habitable room in a home with more than one floor, and 10,000 mm² in a single-storey home. That gap is one reason continuous extract is easier to design around, especially when windows are being replaced.

What extract rates does a dMEV fan need?

Each dMEV fan has two jobs. Its high (boost) rate must meet the minimum for the room it serves, and the trickle rates of all the fans added together must meet the whole-dwelling rate.

RoomMinimum high (boost) rate for continuous extract
Kitchen13 l/s
Utility room8 l/s
Bathroom (with or without a toilet)8 l/s
WC (sanitary accommodation)6 l/s

The total trickle rate across all the fans in the home must meet the minimum whole-dwelling ventilation rate:

Number of bedroomsMinimum whole-dwelling rate
119 l/s
225 l/s
331 l/s
437 l/s
543 l/s

Add 6 l/s for each bedroom above five. The whole-dwelling rate must also be at least 0.3 l/s per m² of internal floor area, counting every floor, so use whichever figure is higher. A three-bedroom house with 110 m² of floor area needs 33 l/s, not 31 l/s.

If a fan’s continuous rate already meets the room’s high rate, it doesn’t need a separate boost setting.

These are installed rates, not catalogue figures. Duct length, bends and grilles all cut real-world airflow, which is why commissioning matters. Every fan in our dMEV range lists its trickle and boost airflow, so you can check it against these tables before you order.

How do you wire a dMEV fan?

A dMEV fan needs a permanent live so it can run continuously, plus a switched live if you want the light to trigger boost. Most fit a standard 100 mm wall or ceiling opening, so they can often go straight into an existing fan position. A fan with an overrun timer usually already has both feeds. A basic fan powered only from the light switch will need a permanent live adding. A qualified electrician should do the work.

Typical wiring for a dMEV fan includes:

  • Permanent live and neutral: keeps the fan running at trickle speed.
  • Switched live (optional): triggers boost when the light goes on. You don’t need it if the fan uses a built-in humidity or motion sensor.
  • Fan isolator: usually a three-pole isolator, so both live feeds can be disconnected for maintenance. Fit it outside the bathroom zones.

In a room containing a bath or shower, Section 701 of BS 7671:2018+A4:2026 (the IET Wiring Regulations) requires 30 mA RCD protection for all low-voltage circuits serving the location. Equipment in zones 1 and 2 needs at least IPX4. Check which zones the fan is approved for. Where a fan has to sit close to a bath or shower, a safety extra-low voltage (SELV) model such as the Vent Axia Revive 7 SELV may be needed. Always follow the manufacturer’s wiring instructions.

For a separate WC, boost the fan from the light switch, a PIR or a manual switch rather than a humidity sensor. Approved Document F says humidity controls shouldn’t be used in sanitary accommodation, because odour is the main pollutant there.

Is fitting a dMEV fan notifiable work?

In England, electrical work in a home is notifiable under Part P if it involves any of the following:

  • installing a new circuit
  • replacing a consumer unit
  • adding to or altering an existing circuit in a special location

In a room containing a bath or shower, the special location runs from the floor up to 2.25 m, or to the shower head if that is fixed higher. Horizontally, it extends 0.6 m from the edge of the bath or shower tray, or 1.2 m from the centre of the shower head where there’s no tray.

Replacing an extractor fan using the existing cabling doesn’t need to be notified to building control. Running a new permanent live for a dMEV fan is different. If that cable alters a circuit within the special location, or you add a new circuit, the work is notifiable.

The simplest route is an electrician registered with a competent person scheme such as NICEIC, NAPIT or ELECSA. They can self-certify notifiable work and issue the certificate without a separate building control application.

What this means for homeowners

If your electrician swaps your bathroom fan for a dMEV fan on the existing wiring, building control doesn’t need to be told. If they have to run a new cable near the bath or shower, ask for a Building Regulations compliance certificate once the job is finished.

How should a dMEV fan be commissioned?

A dMEV fan should be set up for the room it serves, not just switched on. Commissioning usually runs in this order:

  1. Set the trickle and boost speeds to meet the required rates for each room.
  2. Measure the installed airflow at each fan with a calibrated air flow meter and hood, on trickle and on boost, with trickle vents open and doors and windows shut.
  3. Check that background ventilators are fitted, open and the right size, and that none are in wet rooms.
  4. Check that internal doors are undercut.
  5. Complete the installation and commissioning checklist in Appendix C of Approved Document F.
  6. Give the homeowner written guidance on how the system works, what each setting is for and how to maintain it.

For a new dwelling, the airflow test results must reach the building control body within five days of the final test, and a commissioning notice must be given as well.

Can you swap an intermittent fan for a dMEV fan?

Yes, and it’s one of the most common upgrades in homes with condensation problems. The fan itself is usually the easy part.

Before you swap the fan, check:

  • Wiring: is there a permanent live? If not, plan the new feed and check whether it’s notifiable.
  • Opening and duct: most dMEV fans fit a 100 mm opening, but the duct run must be short and clear enough for the fan to reach its rated airflow.
  • Background ventilation: do the habitable rooms have trickle vents? If not, add them, because the fan relies on replacement air. Our air vents and ducting range includes through-wall vents.
  • Door undercuts: make sure air can pass from habitable rooms to the wet room.
  • Open-flued appliances: if the home has an open-flued gas boiler, gas fire or solid fuel stove, continuous extract could affect how it vents. A spillage test may be needed, so get a Gas Safe registered engineer (or a HETAS installer for solid fuel) to check.
  • Fan settings: set the trickle and boost rates to suit the room, using the tables above.

Fitting dMEV throughout the home, rather than in one room, makes it the home’s ventilation system. Every wet room then needs a fan, and the background ventilation should meet the requirements above.

What changes under Approved Document F 2026?

Approved Document F 2026 applies to building work in England from 24 March 2027. Projects already under way may be finished under the 2021 edition during the transitional period, so confirm with the building control body which edition applies.

What stays the same

  • Continuous mechanical extract can be used in any dwelling, whether less airtight or highly airtight.
  • The high rates (13 l/s kitchen, 8 l/s utility and bathroom, 6 l/s WC) and the whole-dwelling rates in the tables above are unchanged.
  • Background ventilators for continuous extract still need 4,000 mm² equivalent area per habitable room, none in wet rooms, and at least the number of bedrooms plus two.

What’s new or more detailed

  • Ducting: decentralised fans should use rigid duct, kept to 2.0 m where practical. Longer runs need design calculations sent to building control. Flexible duct is limited to 200 mm for the final connection, and the external terminal needs a free area of at least 90% of the duct’s.
  • Airflow measurement: continuous fans should be measured with a powered flow hood, accurate to ±5% and calibrated by a UKAS-accredited centre within the last 12 months. A vane anemometer is only accepted for intermittent fans.
  • Competence: apart from a single intermittent fan in an existing home, whoever commissions mechanical ventilation should belong to an organisation that independently checks their competence, such as a competent person scheme.
  • Existing homes: new fans with more than 2 m of duct, or more than one 90° bend, should be airflow tested.

Why dMEV matters more under the Future Homes Standard

The notional dwelling that sets the energy target for new homes in England uses dMEV, with an airtightness of 4 m³/(h·m²) at 50 Pa. Developers can choose other systems. But a home designed below 5 m³/(h·m²) counts as highly airtight, and Approved Document F only gives natural ventilation guidance for less airtight homes. Most new homes will therefore need dMEV, centralised MEV or MVHR.

Wales published its own updated Approved Document F on 7 April 2026, taking effect on 4 March 2027. We’ll update this guide as both editions come into force.

dMEV fans and Building Regulations FAQs

Can trickle vents go in the bathroom?

Not where the bathroom has a continuous extract fan. Approved Document F says background ventilators for continuous extract systems shouldn’t go in wet rooms, because air would flow straight from the vent to the fan instead of ventilating the rest of the home.

Do trickle vents need to stay open?

Yes. Background ventilators should be left open so replacement air can reach the dMEV fans. Closing them reduces airflow through the home and makes the fans less effective at removing moisture. The commissioning checklist in Approved Document F includes checking that they’ve been left open.

What if a habitable room has no trickle vent?

Add a trickle vent to the window frame or fit a through-wall background ventilator. In a home with continuous extract, each one needs at least 4,000 mm² equivalent area, and the home needs at least as many ventilators as bedrooms plus two. Check the manufacturer’s equivalent area, not the size of the slot.

Is replacing a bathroom fan with a dMEV fan notifiable?

Not if the new fan uses the existing cabling. It becomes notifiable under Part P if you add a new circuit, or if running a permanent live alters a circuit within the special location around the bath or shower. An electrician registered with a competent person scheme can self-certify that work.

Can dMEV be used in any home?

Yes. Approved Document F lists continuous mechanical extract ventilation as suitable for all dwellings, both less airtight and highly airtight. Natural ventilation with intermittent fans is only covered for less airtight homes, which makes dMEV a common choice for new builds and airtight refurbishments.

Does a dMEV fan in a WC need a humidity sensor?

No. Approved Document F advises against humidity control in sanitary accommodation, where odour rather than moisture is the main pollutant. Run the fan at its trickle rate and boost it from the light switch, a PIR or a manual switch. A WC needs a high rate of at least 6 l/s.

Bottom line

A compliant dMEV install is more than the fan. Size each fan to the room’s high rate and the home’s whole-dwelling rate, fit 4,000 mm² trickle vents in every habitable room, undercut the doors and give the fan an RCD-protected permanent live. Then measure and record the airflow. That meets Approved Document F 2021. For new homes from 24 March 2027, add the 2026 ducting and powered flow hood rules.

For running costs and the wider pros and cons, read our guide to the benefits of dMEV fans, or browse our full range of dMEV extractor fans.

For product or trade advice, call our team on 0203 994 5470, email sales@electricpoint.com or use our Contact Form.